Mostrar registro simples

dc.contributor.authorSergio Delijaicov
dc.contributor.authorRODRIGUES, M.
dc.contributor.authorFARIAS, A.
dc.contributor.authorNEVES, M. D.
dc.contributor.authorRoberto Bortolussi
dc.contributor.authorMIYAZAKI, M.
dc.contributor.authorBRANDÃO, F.
dc.date.accessioned2022-01-03T15:02:21Z
dc.date.available2022-01-03T15:02:21Z
dc.date.issued2020-05-12
dc.identifier.citationDelijaicov, S.; RODRIGUES, M.; FARIAS, A.; NEVES, M. D.; BORTOLUSSI, R.; MIYAZAKI, M.; BRANDÃO, F.. Microhardness and residual stress of dissimilar and thick aluminum plates AA7181-T7651 and AA7475-T7351 using bobbin, top, bottom, and double-sided FSW methods. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (INTERNET), v. 108, n. 1-2, p. 277-287, 2020.
dc.identifier.issn1433-3015
dc.identifier.urihttps://repositorio.fei.edu.br/handle/FEI/3496
dc.description.abstractFriction stir welding (FSW) is a relatively new manufacturing process (invented in 1991 at the Welding Institute, UK) and more than 5000 scientific articles have been published in the past 10 years in indexed journals demonstrating the robustness of the research. However, further research is necessary to ensure safe use of the technique for structural components, particularly with reference to the aeronautics industry. Residual stresses and their consequences on the life of welded products must be fully understood, in addition to their correlations with other properties such as hardness, strength, and microstructure. This paper is a part of the research being conducted to evaluate the impact of four FSW techniques (bobbin, top-sided, bottom-sided, and doublesided) on the mechanical properties in dissimilar thick joints (12.7 mm) of aluminum alloys (AA7181-T7651 and AA7475- T7351) used in the aeronautics industry. The residual stresses were measured using the incremental blind hole technique and analyzed using the integral method. The longitudinal residual stresses were all positive, with values between 100 and 200 MPa in the stir zone, whereas the transverse ones were all negative, with values between 0 and − 100 MPa. It was possible to verify that the Bobbin process produced lower values of residual stresses and demonstrated better stability in its distribution compared to all the other FSW methods tested.
dc.relation.ispartofINTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (INTERNET)
dc.rightsAcesso Restrito
dc.subjectAA7181-T7651
dc.subjectAA7475-T7351
dc.subjectFSW
dc.subjectBobbin joint
dc.subjectTop-sided joint
dc.subjectBottom-sided joint
dc.subjectDouble-sided joint
dc.subjectResidual stress
dc.titleMicrohardness and residual stress of dissimilar and thick aluminum plates AA7181-T7651 and AA7475-T7351 using bobbin, top, bottom, and double-sided FSW methodspt_BR
dc.typeArtigopt_BR


Arquivos deste item

ArquivosTamanhoFormatoVisualização
Delijaicov_pdf6.939Mbapplication/pdfVisualizar/Abrir

Este item aparece na(s) seguinte(s) coleção(s)

Mostrar registro simples


© AUSJAL 2022

Asociación de Universidades Confiadas a la Compañía de Jesús en América Latina, AUSJAL
Av. Santa Teresa de Jesús Edif. Cerpe, Piso 2, Oficina AUSJAL Urb.
La Castellana, Chacao (1060) Caracas - Venezuela
Tel/Fax (+58-212)-266-13-41 /(+58-212)-266-85-62

Nuestras redes sociales

facebook Facebook

twitter Twitter

youtube Youtube

Asociaciones Jesuitas en el mundo
Ausjal en el mundo AJCU AUSJAL JESAM JCEP JCS JCAP